Hypersonic Models

This is a full-length resin exhaust and nozzle set with the specific detail for EA-6B Prowlers which have an upgraded engine and different nozzle to the A-6 Intruder family. The instructions are based on fitting it to the Kinetic/Italeri kits, but the modeller may be able to adapt them to the Revell..

Corrected tail surfaces (stabilisers, elevators and rudder) for the Kitty Hawk FJ-2 Fury (and early FJ-3). The FJ-2 kit only contains the ribbed elevators/rudder, which is correct for an FJ-3 and very late FJ-2's after transfer to the Reserves. FJ-2's in service (as well as early FJ-3's) had smooth-..

This is an airframe update set for Kitty Hawk's FJ-2 Fury. It includes a new intake nose ring with a corrected shape (the kit's nose is much too blunt) and cast-on one-piece air intake front part. There is detail scribing on the inside of the nose ring (absent on the kit parts). The nose wheel well ..

This is a TISEO pod for the Meng F-4E kit, 1:48. The pod parts are 3D printed and the glass is a cast clear resin piece. A paint mask is provided as well...

Stabilator for all types of F-4 Phantom that used the unslotted stab. For both the Hasegawa and Academy kits. Includes separate PE pivot cover plates and stiffener "fishplates" (for Air Force variants). The stabs can be used as a drop fit replacement for the kit parts or, with some work on the kit p..

F-4 Phantom outer pylons, Air Force type, 1:48, designed for the Zoukei Mura line of kits. The pylons have the correct outboard angle built in and come with separate sway brace pins so stores can be mounted at correct angles, either canted in line with the pylon or perpendicular to the ground...

This is a set of Navy type outer wing pylons designed to fit the Zoukei Mura Phantoms (J and S). The set comes with separate sway brace pins so the modeller can adapt them completely free to the specific store and correct outboard angle (in case of MER or TER installed). The photos show the pylon bo..

This is a set of aft fuselage half parts that correct the shape error on the engine shoulders of the Zoukei Mura short nose Phantoms. in addition to the re-shaped geometry, some surface detail has been improved. Please note that this is not a drop-fit replacement set. Cutting of the fuselage is requ..

Detail parts for the inner canopies on F-4 Phantoms. The set comprises of resin and PE parts for windscreen, forward-, centre- and rear canopies and includes canopy actuator jacks, safety uplocks (optional installation), detailed downlocks, forward and rear compasses and various detail parts for the..

Corrected A/C air intakes for Academy's F-4 Phantom series (F-4B, C and D so far). Drop fit resin replacement. All it takes is a little superglue and a swipe of filler to blend it in...

F-4 Phantom C/L pylon, 1:48, for the Tamiya line of kits. The pylon fits on and into the moulded-on mounting tab between the Aux doors on Tamiya's kit with a simple modification (it needs to be shortened and slightly re-shaped). The pylon set comes with two sets of separate pins - one for the larger..

Hollowed, thin-walled resin part to detail the open-ended Jet Fuel Starter (JFS) exhaust tubing as found on modern Eagles, such as the F-15C and F-15E Strike Eagle. A small part that adds detail and interest to this area and brings it up to date on all 1:48 F-15 kits...

These are 3D printed face curtain handles for MB Phantom ejection seats. The handles are mainly designed for the Hypersonic Models Mk. H5 seats but can be used on other types (H7) and manufacturer's seats as well. The handles are 3D printed but from a slightly elasctic resin that doesn't break as ea..

This is a backdate set for the (new tool) Kinetic F-16A kit and contains parts to build Block 1,5 and 10 aircraft. The set includes small stabilators with thin static wicks, early instrument panel and coaming, Environment Control System (ECS) exhaust panel, RWR and rectancular UHF antennas. The stab..

A set of two Martin Baker Mk. H5 ejection seats for early F-4B, F-4C and F-4D Phantoms (until around 1970). Suitable for and tested with Academy, Hasegawa and Zoukei Mura kits. The seats have cast on seat belts which differ from each other...

This is a set of corrected engine nacelles with intakes, exhausts and pylons for the Trumpeter A-3 Skywarrior kits in 1:48. Suitable for all variants. This set also includes parts that enable the modeller to build the kit with dropped flaps. Please note that the first print run of the instructions m..

This is a set of full-length and correctly angled jet exhaust tailpipes for the A-6 Intruder family (A-6A, A-6E, A-6E TRAM, EA-6A). It contains detailed, thin-edged nozzles as well as detailed J-52 engine end with guide vanes and probes. The set is designed for the HobbyBoss Intruder kits (and the i..

This set contains a pair of 1:72 outer wing pylons with weapons adapters for USN and USMC Phantoms (and some early USAF ones as well). Suitable for all brands of 1:72 Phantom kits...

Stabilator for all types of F-4 Phantom that use the slotted stab. For both the Hasegawa and Academy kits. Includes separate PE pivot cover plates and stiffener "fishplates" (for Air Force variants). The stabs can be used as a drop fit replacement for the kit parts or, with some work on the kit plas..

Here is full set of resin wheels for Revell's 1:48 SR-71 kit. The wheels come with all correct detail, including brake detail and even the brake line connectors on the main wheel hubs. The anti-skid generator brackets are provided as delicate photo etch parts. The main wheels are NOT two identical s..

This is a replacement resin fin tip for the HobbyBoss Intruder family. The HB fin tip has the wrong shape and once you have noticed the error you can't ignore it any longer...the surface detail is slightly corrected and enhanced as well. The required cut on the kit is fairly simple as it's along a p..

This is a cockpit set for Kitty Hawk's FJ-3 Fury kit (1:48). It includes a corrected and detailed seat with parachute and harness in place (which differs from the FJ-2 seat in several details), a detailed rear cockpit bulkhead and turtle deck, the FJ-3 specific antenna assembly (3D printed part) as ..

This conversion set includes the AN/ANQ-126 fairings for the intakes (with mounting holes to match Tamiya's moulded-on pins), a fin cap with the correct sensor bulge for the N model, a new RIO instrument panel and an external rear view mirror. Further N specific parts are already included in the Tam..

This is a slat-wing conversion set for the Zoukei Mura F-4E (early), hard wing kit. This set contains slatted outer wings (cast in a special hard resin to prevent warping) and inboard slat inserts. No cutting is required for installation. In addition, the set contains a multi-part belly reinforcemen..